Hunter Pump Start Relay Wiring Diagram
Close and lock the cabinet door. Unplug the power supplies to the pump switch as well as the. 2) run a single wire from the mv/pump terminal on the. Install pump start relay cover plate and four screws.
hunter relay wiring diagram
hunter relay wiring diagram hunter pump start relay wiring 2nd Gen sharing a pump start relay with a Hunter Controller
Connect A Common Wire To The C (Common) Terminal Inside The Controller And Connect The Remaining Wire From The Pump Start Relay To The P (Pump) Terminal.
Connecting the pump start relay should only be done by a licensed electrician following local. The two red wires are. In stock (3) save 27 %.
Enclosure Measures 7.5 H X 6.5 W X 4.5 D.
Web wire size to connect the relay to the timer will normally be 18 awg. Web use wire nuts to make the connections and verify they are secure. Web (common) and the remaining wire from the pump relay to the.
Web Web A Pump Start Relay Is A Relay Box That Activates A Pump Every Time A Zone Is Activated From The Controller.
The relay can be located up to 800’ away from the timer using 18 awg wire. Makes connections to controller quick and easy. Locate the two thinnest wires extending from the pump start relay, and strip 1/2 inch of insulation from the end of both wires using the wire strippers.
Installation Instructions Mounting The Relay Note:
Double pole / single throw pump start relay for 120vac pumps up to 2 hp or 240vac pumps up to 3.5 hp. Relay holding current draw must not exceed.28 amps (24 vac). Do not connect the controller.
Web Web February 22, 2022 By Jenny Fresh.
Complete this section only if you have a pump and pump start relay installed. Use wire nuts to make the connections and verify they are. Web 1) run a single wire from the “common” terminal on the controller to one of the yellow wires on the pump start relay.
Web The Product Is Fully Compatible With All Standard 24Vac Controllers.
A pump start relay is an electronic device that uses a signal current from the irrigation. Run a single wire from the p/mv terminal on the controller to the other yellow wire on the pump start relay. The distance isn’t a problem, just like a solenoid on a sprinkler.
That Will Be Shorter Distance With All The Wires Involved.
![2nd Gen sharing a pump start relay with a Hunter Controller](https://i2.wp.com/community.rachio.com/uploads/db1097/original/2X/7/73a73dcfc6af57393e1adec4d18dccbbe4de4ec5.jpg)
![hunter pump start relay wiring diagram](https://i2.wp.com/mainetreasurechest.com/wp-content/uploads/2020/05/pump-start-relay-wiring-elegant-unique-wiring-diagram-for-electric-fan-relay-diagram-of-pump-start-relay-wiring.jpg)
![Connecting a pump start relay Hunter PROC (PCC) User Manual Page](https://i2.wp.com/www.manualsdir.com/manuals/720786/14/hunter-pro-c-pcc-page14.png)
![2nd Gen sharing a pump start relay with a Hunter Controller](https://i2.wp.com/community.rachio.com/uploads/db1097/original/2X/7/7cba25e98e860e687f891eca364b411e74aefc52.png)
![hunter relay wiring diagram](https://i2.wp.com/detoxicrecenze.com/wp-content/uploads/2020/05/how-to-wire-an-orbit-pump-start-relay-mg-4279-pump-start-relay-wiring-diagram-also-pump-start-of-how-to-wire-an-orbit-pump-start-relay.jpg)
![Hunter Pump Start Relay PSR22 loud noises Wired Flow Sensors](https://i2.wp.com/community.rachio.com/uploads/db1097/original/2X/1/1be23c6299976a5806b8a45a569f905a994ef45f.jpg)